বার্তা পাঠান
বাড়ি খবর

কোম্পানির খবর ছাদ পত্রক মেশিন বিচ্যুতি কীভাবে সামঞ্জস্য করবেন?

সাক্ষ্যদান
চীন Cangzhou Best Machinery Co., Ltd সার্টিফিকেশন
চীন Cangzhou Best Machinery Co., Ltd সার্টিফিকেশন
ক্রেতার পর্যালোচনা
আমি Cangzhou BEST Machinery Co., Ltd এর সাথে খুশি। খুব পেশাদার এবং reiable কারখানা। তারা ভাল মানের মেশিন এবং ভাল বিক্রয় সার্ভার অফার করে, তাদের সাথে আবার সহযোগিতা করার জন্য সামনের দিকে তাকান।

—— ময়ো

Cangzhou BEST মেশিনারি কো., লিমিটেডের মেশিন খুব ভাল, এবং উত্পাদন দ্রুত, বিতরণ দ্রুত। খুব টার্স্টফুল কোম্পানি।

—— অক্টাভিও

আপনার সদয় আতিথেয়তার জন্য ধন্যবাদ. আপনার কোম্পানী খুব পেশাদার, আমরা নিকট ভবিষ্যতে চমৎকার সহযোগিতা হবে.

—— ক্রিস্টিয়ান

খুব ভাল কোম্পানি। খুব ভাল যোগাযোগের মাধ্যমে সমস্ত সমস্যা সমাধান করা হয়েছে, আমার ক্রয় নিয়ে সন্তুষ্ট।

—— স্পেন্স

very professional factory, realiable, happy with them

—— Samuel

ভাল বিক্রয় পরিষেবা, ডেলিভারি সময় দ্রুত। ভাল যোগাযোগ।

—— আলী

তোমার দর্শন লগ করা অনলাইন চ্যাট এখন
কোম্পানির খবর
ছাদ পত্রক মেশিন বিচ্যুতি কীভাবে সামঞ্জস্য করবেন?
সর্বশেষ কোম্পানির খবর ছাদ পত্রক মেশিন বিচ্যুতি কীভাবে সামঞ্জস্য করবেন?

(1) The level of the tile press machine is not adjusted properly, you can use a level ruler to straighten the channel steel at both ends of the machine, and the four legs of the machine are properly leveled with some iron plates.
(2) Find a large square ruler, measure the feed ruler behind the tile press, that is, the angle iron of the plate and the wheel of the tile press to find the right angle, this is very important, if the rear plate is not a right angle The color board must not go straight.
(3) Measure the diagonal of both ends of the machine to see if they are consistent, provided that the machine is adjusted horizontally. According to experience, the diagonal angle is less than 4 mm and can be adjusted. If it is greater than 4 mm, it is difficult to adjust. Even if it is adjusted, the walking plate is unstable.
(4) When encountering a machine that deviates, the principle is to look in the direction of entering the board, and in which direction the board runs, pad the feet of that machine. In fact, the diagonal is artificially adjusted to be consistent.
(5) Finally, measure whether your color steel equipment and the color steel coil you put are on a parallel line. Reminder: Deviation generally occurs after the color steel coil is replaced, and the coil and the machine are not in a straight line (the coil and the machine cannot be too close to maintain a distance of about 3 meters), resulting in the deviation of the board and the deviation of the tile

পাব সময় : 2020-04-22 11:48:55 >> খবর তালিকা
যোগাযোগের ঠিকানা
Cangzhou Best Machinery Co., Ltd

ব্যক্তি যোগাযোগ: Mr. Arno Hao

টেল: +8618717894416

আমাদের সরাসরি আপনার তদন্ত পাঠান (0 / 3000)